For a generation, the default position for a fast, flat-shooting, hard-hitting cartridge has been 7mm, .284-inch. In the 1950s, while Jack O’Connor was touting his beloved .270s, other notables like Les Bowman and Warren Page were pushing the fast 7mm with its traditionally long, heavy-for-caliber bullets. Oddly, Remington’s excellent .280 Remington (1957) on the .30-06 case didn’t take off. Neither did the belted 7×61 Sharpe & Hart. Probably because of availability, it was only factory-chambered by Danish firm of Schultz & Larsen.
By
Craig Boddington
We Americans love our .30-calibers. The .30-06 is still popular and powerful. It’s little brother, the .308 Winchester is, after the .223, America’s most popular centerfire. These days, many folks want to shoot a bit farther, so we want faster cartridges that shoot flatter. Plenty of fast .30s, but with speed comes recoil. For many, a magnum .30-caliber is too much of a good thing. And, unless we do a lot of hunting for game larger than deer, magnum .30 performance isn’t necessary.
Boddington, Charlie Barnes of Flat Creek Precision, and Zack Aultman, on Zack’s range in Georgia…messing with a Flat Creek 7 PRC.Continue reading “WHICH 7MM FOR YOU?”
When selecting a hunting cartridge, three considerations are most important: Accuracy, shooting ranges, and power, all adequate for the game to be hunted. These apply for hunting any game from prairie dogs to pachyderms.
For varmints, power might seem a silly consideration, so let’s consider that first. The word “varmint” is uniquely American, a corruption from the English “vermin.” The implication is noxious pests, generally removed with minimal restrictions (such as seasons, bag limits, and license requirements). The game Americans generally consider “varmints” range from grass-eating and hole-digging rodents up to coyotes. The distinction can change. In British East Africa (now Kenya and Tanzania), lions were classed as vermin until late in the game. In Europe, the marmot (relative to our woodchuck) is highly prized, often hunted with seasons and limits. In North America, “furbearers” often have separate seasons, sometimes a separate license.
Coyotes are extremely tough animals, but almost all centerfire cartridges are more than adequate. This coyote was taken with a 6.5 PRC, plenty of gun but from .223 Remington upward pelt damage is inevitable.
Because of numbers and voracious predation, rules for coyotes are usually liberal. It’s old Wile E. Coyote that calls up the power question on varmint cartridges. From small gophers to the largest woodchuck, any of the rimfires on up are powerful enough, just a matter of how close you must get.
Coyotes are different, pound for pound for pound very tough animals. Power doesn’t matter so much if the encounter is close. However, unless one is calling, coyote encounters aren’t often close. For me, coyote hunting is a centerfire game. Which one depends on required range, and whether pelt damage is a concern. Serious callers (which I am not) often use shotguns with heavy charges of coarse shot. Easier to hit moving coyotes coming to the call, and minimal pelt damage past 25 yards.
For a May 2024 prairie dog shoot in Wyoming Gordon Marsh hauled the guns. These include .17 HMR, .22 Hornet, .204 Ruger, .223 Rem, and .22-250, a fine selection for all ranges and conditions.
The .17 Remington was developed in Australia, no coyotes but problems with non-native foxes. Light, frangible .17-caliber bullets tend to enter and come apart without exiting, so wonderfully effective without ruining the pelt. The popular .17 HMR rimfire is an awesome medium-range varmint cartridge, but marginally powerful for coyotes unless the shot is close. Today we have centerfire .17s from .17 Hornet up through grand-dad .17 Rem. Plus the rimfire .17 Winchester Super Magnum and the .22 WMR. All are adequate for coyotes, effective range depending on velocity. Above that, the .204 Ruger and all the .22 centerfires are fine for coyotes.
Hornady’s Seth Swerczek with a .17 HMR, shooting prairie dogs from field positions. The little .17 HMR punches far above its weight class, surprisingly effective to 200 yards…until the wind comes up.
I do little specific coyote hunting. The majority I take are targets of opportunity while hunting other game. This means I’m usually carrying a centerfire adequate for deer-sized game. Effective for coyote control, but don’t expect salvageable skins. A partial compromise is to use a milder .22 centerfire like the .223 Rem with non-expanding military or FMJ match bullets. Caliber-size entrance and exit holes are common. Just check your regs; non-expanding bullets aren’t legal for hunting in some jurisdictions. Also, poor choices for other varminting. Frangible “varmint” bullets aren’t quick-expanding just for explosive effect; also, to reduce ricochet.
They look cute, but prairie dogs consume prodigious quantities of grass and destroy pasture with burrows and mounds. They offer a target of maybe 12×3 inches, a difficult mark on the usually-windy prairie.
The varmint hunting I know best is small rodents: Ground squirrels in California, prairie dogs on the Great Plains, both found in colonies. I’ve done some rockchuck shooting in the West, but I can count all the woodchucks I’ve shot without taking my shoes off. Power isn’t an issue. I’ve had great fun shooting prairie dogs with .22 Long Rifle hollowpoints, Some serious Eastern hunters make a game of stalking woodchucks with rimfires.
Introduced 96 years ago as America’s first varmint cartridge, the little .22 Hornet is faster and more effective than it looks. Also shockingly accurate, as proven by this CZ .22 Hornet.
Wherever, shooting rodents isn’t about raw power, but about accuracy and range, which sort of go together. Prairie dog shooting is perhaps the most demanding of raw accuracy. Small targets open country, usually windy. An adult prairie dog might offer a target as much as twelve inches nose to tail, more like three inches from brisket to backline. Presentation may be anything, but is usually either standing vertically, or horizontal. Either way, there’s a large target in one direction, very small the other.
We typically judge rifle accuracy by average group size. In America, usually at 100 yards. For a hunting rifle, the Holy Grail is generally one Minute of Angle (MOA), even for mountain game. One MOA means one inch at 100 yards, natural dispersion spreading to two inches at 200 yards, three inches at 300 yards, and so forth.
The Ruger No. 1 isn’t known for tack-driving accuracy, but heavy-barreled models are often surprising. This is Boddington’s favorite varmint rifle, a stainless-and-laminate No. 1 in .204, a genuine half-MOA rifle.
On the windy prairies, and with animals often moving while bullets are in flight, there’s no such thing as hitting prairie dogs with every shot. I prefer hitting to missing. When I inevitably miss, I like to understand why, then correct with the next shot. Doesn’t do me any good to miss because I’m out of accuracy. So, for a general-purpose prairie dog rifle, one MOA accuracy isn’t enough. That means I’m beyond Minute of Prairie Dog at 300 yards. That’s a fair poke on a prairie dog-sized target, nobody hits them all. However, if you start with one-inch groups at 100 yards, naturally expanding groups will cause misses beyond 300 yards. Since I like hits better than misses, I expect a serious prairie dog rifle to do better. No such thing as too much accuracy for small varmints. Also, no limited to how far one can shoot at prairie dogs! Only a few blessed and gifted rifle barrels will deliver one half MOA groups on a consistent basis, but that’s the goal.
This heavy-barreled Ruger No. 1 in .204 Ruger belongs to Gordon Marsh. He and Boddington both believe the .204 is the best all-around choice for prairie dogs: Plenty of range, but mild recoil allows calling shots through the scope.
It’s not about cartridges. However, my heavy-barreled Ruger No. 1 in .204 Ruger will do that. In May 2024, I was delighted to see that friend and prairie dog shooting partner Gordon Marsh found a No. 1 in .204 that will also do that. I’ve had various other .22 centerfires that grouped as well or better, also 6mms and some larger cartridges.
That level of accuracy is not essential. It’s just that, with less accuracy, effective range is limited. Well, absent wind-bucking and trajectory-flattening velocity, range is limited anyway. On prairie dogs, that’s part of the fun; just depends on how personal you take misses.
Gordon Marsh on the bench in a prairie dog town with his heavy-barreled Savage .22-250. When the wind comes up and shots are long, it’s time for the “big gun.”
The last time I shot prairie dogs with a .22 rimfire was with a Ruger 10/22 target rifle. It averaged .75-inch 50-yard groups across several loads. Theoretically, Minute of Prairie Dog to 400 yards. Between ridiculous holdover, huge wind deflection, and long flight time, you’re not going to hit many prairie dogs at 400 yards with a .22 Long Rifle. Once I figured holdover and wind, it was deadly at 100 yards, and I was surprised at how consistently I could hit at 150 yards. Then, I was done, time to break out a faster cartridge.
An accurate .22 LR is a wonderful varmint rifle, just need to keep shots short. This Ruger 10/22 target model was wonderful fun on prairie dogs, effective to a bit past 100 yards.
In our prairie dog group, Bill Green and Ronnie Whitten love their .17 HMRs. Amazing accuracy, uncanny performance. I’ve seen them hit prairie dogs at 300 yards too often to be flukes. However, the .17-caliber’s light bullets are extremely susceptible to wind, great training to learn to deal with it, but the .17 HMR is pretty much done at 200 yards.
Gordon Marsh in a Wyoming prairie dog town with his suppressed CZ .22 Hornet, amazingly effective to nearly 300 yards. Behind him, Bill Green is shooting a .223, always an effective varmint cartridge.
This year, Gordon borrowed another page from my book and also brought a CZ .22 Hornet. Introduced in 1930, the Hornet is America’s first factory varmint cartridge. Despite its archaic rimmed, tapered case, it is shockingly accurate and surprisingly fast; lighter bullets can be loaded to nearly 3000 fps. Fitted with a suppressor, the little Hornet turned out to be Gordon’s primary prairie dog rifle this year. When it was calm, I was impressed to see how consistently he was hitting clear to 300 yards. When the wind came up, he was done, needed something faster.
Left, a heavy-barreled .22-250; right, a .25-06. Both these rifles have the extreme accuracy needed for long-range varminting. A .25-06 with light bullets is probably the most powerful cartridge that makes sense for varminting. Above .22, a primary drawback is too much recoil.
Since power isn’t an issue, prairie dogs can be shot with anything that’s accurate enough. Kansas friend Vance Cain told me he used to shoot prairie dogs with his .458. When I was a kid, I shot a lot of prairie dogs with my .264, and my “go-to” was a .243. Many folks use various 6mms and .25-calibers with light bullets. The .22-250 reigns as the most popular “fast” varmint cartridge. I used the .22-250 for years, and Gordon always has his heavy-barreled Savage .22-250, his “big gun,” brought out when the wind comes up or only distant ‘dogs are visible.
A 6mm ARC set up in a prairie dog town. Accurate and flat-shooting, all the 6mms are effective for varminting. The major drawback: Too much recoil to call shots through the scope.
There are many great varmint cartridges: All the .17s, .20s, .22s, even the 6mms and .25s if one prefers. Some are old, some new. Both the 6mm ARC and brand-new .22 ARC have been wonderfully successful. The .22 ARC has similar velocity to .22-250, but AR-compatible, and barreled with faster twist to use heavier bullets, which buck wind better, but produce more recoil.
Although there are many other good choices, these are Boddington’s favorite varmint cartridges, left to right: .17 HMR, .22 Hornet, .204 Ruger, .223 Rem, .22-250. On a given day, which is used depends on game, distance, and wind.
Unlike much varmint shooting, prairie dogs tend to offer multiple opportunities. So, for me the ideal prairie dog rifle has lots of reach, but mild enough recoil to allow calling shots through the scope. Call the wind, take the shot, see the strike, reload and adjust. The .223 allows this. Unless very heavy, the .22-250 bounces just a bit too much, as do all larger cartridges. The .204 is faster but, with lighter bullets, has less recoil; it has become my favorite all-around varmint cartridge.
I often claim that I’m the world’s worst turkey hunter. Possibly not true, but when I tell you what I did last week, you’ll believe me.
Turkey guns and loads have come a long way.
By
Craig Boddington
I often claim that I’m the world’s worst turkey hunter. Possibly not true, but when I tell you what I did last week, you’ll believe me. I was trying to get a Rio Grande gobbler on my kids’ place in Texas. Running out of time, I took a final cruise down the power line road, stopped foe one more call. Good grief, a gobbler cut loose. Not far away. Grabbed the shotgun, pumped the action, ducked into the woods.
: Boddington’s first gobbler taken with TSS was taken in Georgia in 2023, using a Mossberg semiauto 12-gauge with Apex No. 8 shot. The shot was past 40 yards; the bird went straight down.
I found a perfect tree to sit against, got the gun across my knees, went to work on the slate. Double gobble, closer. Couple minutes later I saw the red head. Then another. Two nice gobblers, coming straight in. Both were good birds. When they were about 30 yards away I held the bead low on the neck of the larger tom…and heard the loudest CLICK ever. Plenty loud for the turkeys, too. They were gone. My fault or the gun? I know I pumped the action, but the bolt didn’t pick up a shell. And so ended my 2024 Texas turkey hunt.
The shell that I didn’t fire was a Hornady 12-gauge three-inch, nickel-plated No. 5 shot. Those were good shells, shot several gobblers with them. Still have a few, so I may shoot another turkey before they’re gone. Provided I can remember to load my darned gun. I was sad when Hornady got out of the turkey load business. I asked why and was surprised at the answer: “Turkey loads are getting ever more specialized.”
Donna Boddington and Zack Aultman with a nice Eastern gobbler, taken with Apex No. 9 TSS in a 20-gauge Benelli.
Man, are they. Not being a truly avid (or expert) turkey hunter, I missed much of this. Those Hornady turkey loads were good shells, though not much different from good shells I’ve used most of my life: Heavy payload of high-quality nickel-plated lead shot. Today, there are at least a dozen types of shot on the market. I don’t claim to have experience with all. I’ve shot couple of turkeys with bismuth shot, pretty good stuff. One, years ago, with steel shot duck loads. It worked, but I don’t recommend that. HD and Hevi Shot, both tungsten alloys, are excellent.
I was introduced to HD on a writer’s hunt in Mississippi several years ago, with experimental HD shells from Kent. Incredibly impressive on the pattern board, used them for a couple of gobblers, equally impressive. HD and Hevi Shot are excellent, and the shells are reasonably affordable. However, they aren’t TSS. Tungsten Super Shot (TSS) is easily the deadliest shot to date. Just two years ago my Georgia friend and Eastern gobbler mentor Zack Aultman introduced me to TSS.
Based in Mississippi, heart of turkey country, Apex is just one of several smaller firms offering today’s increasingly specialized turkey loads. This is the load Boddington used in 2023, a full two ounces of No. 8 TSS in 12-gauge three-inch.
As a metal, tungsten is denser than lead. Water has density of 1 g/cc (gram to cubic centimeter). The old standby lead is 11.3 g/cc, while tungsten is a whopping 18.1 g/cc. Tungsten is both heavier and harder than lead. In effect, you can drop down three or four shot sizes, still get more penetration per pellet, and a lot more pellets in your pattern. Because it’s harder and heavier, patterns hold together better. With lead, I’ve always been a No. 5 shot guy on turkeys, although I’ve often used No. 6. Often, I hedge my bet with No. 4 as the second shell in the magazine or in the second barrel. Smaller shot for head shots, larger shot for backup body shots if needed.
Two beautiful gobblers, plenty close. The bird on the left is offering a perfect shot.
With TSS, you can drop down to 8s or 9s, no real need for larger shot for backup. It’s that effective. You can also back off a gauge or two. Less recoil in a lighter gun. With TSS, serious hunters are confidently taking turkeys with .410s. Me, I’m neither that serious, nor that confident. For years, believing bigger was surely better, I used a 10 gauge. More of a fashion statement than a necessity. I went to a 12-gauge long ago, and today I’m perfectly happy with a 20-gauge…with good shells and a tight choke.
Of these five 20-gauge turkey loads, all are TSS except the top center Magnum Blend load, which is Hevi Shot. Only the Federal Premium TSS load is from a major manufacturer.
Last year and this, I took Eastern gobblers at Zack’s place, using Apex shells, loaded in Mississippi. Last year I used a Mossberg 12 gauge with two ounces of No. 8 TSS. One shot at the pattern board to verify. No turkey was going to walk through that pattern. The gobbler I shot was farther than I like, past 40 yards. Didn’t matter.
This year, a week before my comeuppance in Texas, Zack loaned me a 20-gauge Benelli, this time with 1 5/8 ounces of Apex 8 ½ TSS. Again, one shell to verify the pattern. With young Ben Pickren on the call—13 years old and so good I stayed quiet—we had a nice tom come to about 25 yards. Straight down without a wiggle.
That’s good, but this struck me more: I held low on the neck and was concerned the pattern might have messed up the breast. Not a single pellet the breast meat, only couple pellets in the head. The pattern centered exactly where I was aiming, low on the neck. That’s tight.
These patterns were shot at 25 yards with four different 20-gauge TSS loads, using a Rob Roberts choke in a Benelli semiauto. No turkey could walk through any, but the second from left Boss Tom, 1 5/8 ounces No. 9, is clearly the most impressive
With the turkey business done, we had some time to play. Zack dug around camp, found odds and ends of five different flavors of 20-gauge TSS shells. A Federal Premium load was the only one from a major manufacturer. He also found a hatful of 20-gauge turkey chokes.
Bigger isn’t necessarily better. As I wrote in this column a year ago, I lost a turkey pasted center-chest with a 10-gauge. That was poor shot placement: the head was tucked in, bad decision. In truth, my plain-Jane 10 gauge double that I loved threw terrible patterns. Not much development in 10-gauge chokes (or shells) because it’s uncommon and not essential.
Today there are numerous options in shotshells and shot. This Kansas gobbler was taken with Kent No. 7 HD load. HD is a milder tungsten alloy, heavier than traditional lead shot, but not as costly as TSS.
Although the science is hardly new, chokes have developed along with shot and shells. Unfortunately, at the cost of TSS shells, nobody spends a lot of time on the pattern board. Too bad because there is much to learn.
Using a Primos Jellyhead choke, this pattern was fired at 25 yards with Boss Tom’s 20-gauge load, 1 5/8 ounces No. 9 TSS, an amazing pattern.
No way I was going to run through six chokes, and we didn’t have enough shells anyway. I shot my turkey with a Rob Roberts choke, so we patterned it at 25 yards with four loads. No turkey could walk through any of those patterns, but a Boss Tom No. 9 TSS load clearly patterned better than the rest, including the Apex Ninja No. 8 ½ load I’d taken my turkey with.
Sort of randomly, next we tried Primos’ Jellyhead choke tube. Again, in this choke, in this gun, on this day, the Boss Tom load won. Big time. I’m not sure I’ve ever seen a pattern like that before. About 70/30 above/below point of aim, density scary just above point of aim. I prefer high-shooting shotguns and always aim below point of impact. It is said that 60/40 (60 percent above aim, 40 percent below) is ideal, but I’m okay with 70/30. As an old trapshooter, I don’t want a flat-shooting shotgun where I must cover the head. My preferred hold is low neck, so I want a high-shooting shotgun.
Dad and I hunted turkeys in Missouri in the mid-Sixties, when the Ozarks first opened. I maintain my position that I’m not a serious turkey hunter. However, with nearly 60 years of experience, my long-set habits and opinions don’t change easily. Obviously, with better, deeper-penetrating shot and denser patterns, sensible ranges are increased. I know how far some folks are shooting turkeys, but I’m not going there. At 71, it’s like open sights on a rifle. My window has shrunk. I’m a 40-yard guy, do-able with older shells as well as new. Closer is better, but not too close. I’d rather have a pattern to play with, rather than a tight ball of shot.
: Patterning a shotgun off the bench is hard work. With heavy loads, even a 20-gauge has plenty of recoil. It’s not necessary to waste expensive shells, but it’s essential to verify both point of impact and pattern with whatever load you choose.
The most important thing: Essential to pattern your shotgun. We can still kill turkeys with old-fashioned shells. We must be able to because, awesome as it is, TSS has drawbacks. Since it’s harder than lead, it cannot be used in many older shotguns. If okay with steel, it’s probably okay with TSS. I have guns than can’t use either.
Boddington and Ben Pickren with a fine Georgia gobbler, called in by Pickren and taken by Boddington at 25 yards, using a 20-gauge Benelli with Apex TSS No. 9 load.
Then, there’s cost. Frightful. Tungsten is a scarce metal, few mines in the world. Some of the shells we were gleefully flinging at paper targets were ten-dollar shells. Ouch. Although tungsten based, HD and Hevi Shot are alloys that use less tungsten, less expensive. Not as good as TSS, but better than good old lead shot…which is not damning with faint praise. Despite efficacy, I wouldn’t hunt waterfowl with TSS. A turkey, well, kind of a big-game bird. Tasty, but more a trophy hunt than a meat hunt. I baulk hard at a $10 shotgun shell. Much the same cost as .470 Nitro Express. But we only need a few: One to verify pattern and point of aim. One to kill the bird, maybe a spare just in case. With the results I’m seeing, pricey but acceptable.
The .45-70 Government was adopted by the US military in 1873. Amazing that it’s still with us today, more amazing that it’s still popular. Truth is, it almost died away. The .45-70 saw us through the plains campaigns and the last years of bison eradication, but it was our standard-issue military cartridge for just 19 years, replaced by the .30-40 Krag in 1892.
By
Craig Boddington
The .45-70 Government was adopted by the US military in 1873. Amazing that it’s still with us today, more amazing that it’s still popular. Truth is, it almost died away. The .45-70 saw us through the plains campaigns and the last years of bison eradication, but it was our standard-issue military cartridge for just 19 years, replaced by the .30-40 Krag in 1892.
In the 1870s, no repeating actions could handle the .45-70. The 1881 Marlin lever-action came first, followed by Winchester’s answer, the Model 1886. The .45-70 was the most popular of the 1886’s 19 chamberings, but it was long gone before production ceased in 1935. Longer gone were the 1881 Marlin and the original 1895 Marlin.
Because repeaters were costly, through the 19th Century single-shots were more popular. The .45-70 was a common chambering in most big single-shots. However, after the bison were gone and the Great Plains were pacified there was limited need large cartridges. Winchester 1885 High Wall was probably the last classic American single-shot, .45-70 just one of its many chamberings.
This custom .45-70 was built by Idaho riflemaker Jim Brockman 30 yeara ago, before Cerakote or rail mounts existed, and when the “guide gun” concept was brand new. Brockman’s rifle offered three sight options: Conventional scope, LER scope, and aperture on the rear scope base.
The original .45-70 load used a 405-grain lead bullet in front of 70 grains of blackpowder, producing 1330 fps for 1590 foot-pounds of energy. Factory loads were converted to smokeless powder, but because the trapdoor Springfield action is not strong, pressures were kept mild and original ballistics maintained.
Factory ammunition remained available, but from about 1930 no new .45-70 rifles were made. Bill Ruger gets credit for starting the comeback. People thought he was crazy when he brought out his Ruger No. 1 in 1966, the first modern centerfire single-shot. Some folks thought he was even crazier when, early on, he chambered his No. 1 to .45-70, an almost-forgotten relic.
Handloaders already knew what the .45-70 could do in strong actions. Also, thanks to the early success of the .458 Win Mag, introduced in 1956, the .45-70’s .458-inch bullets were common. Gunwriter John Wootters was among the early purchasers of a Ruger No. 1 in .45-70. He took it to Mozambique where, among other animals, it accounted for a huge leopard.
The time of reintroductions and reproductions wasn’t yet, but the .45-70 was back. Its return was secured in 1972 when Marlin introduced their 1895 lever-action in .45-70. Marlin took the name from their original 1895, but the “new” 1895 is based entirely on the 336 action. The process started in 1964 with the Model 444, an internally enlarged 336 adapted to the powerful .444 Marlin. Eight years later, Marlin went a step farther, hogging out the strong 336 action to house the big .45-70.
: This Texas hog was the first animal taken with a Ruger/Marlin 1895 in .45-70. Although the .45-70 has many uses, Boddington loves it for hog hunting: Ranges are usually close, and the .45-70 speaks with authority.
The new Marlin 1895 opened the floodgates, introducing a new generation to the .45-70’s hard-hitting short-range power. Standard factory .45-70 loads are still loaded to mild pressures, ensuring safe use in trapdoor Springfields. Marlin’s 1895 spurred ammunition manufacturers to create a new generation of .45-70 loads, pressures still mild, but with lighter bullets loaded faster, increasing energy and flattening trajectory. Long standard, loaded by multiple firms, is a 300-grain bullet at 1880 fps, yielding 2355 ft-lbs.
Since lever-action 45-70s have tubular magazines, downrange performance was hampered by the necessity to use blunt-nosed bullets. Hornady changed this in 2006 with their Flex-Tip-eXpanding (FTX) bullet with compressible polymer tip, the first sharp-pointed bullet safe for use in tubular magazines. In their LEVERevolution line, these were mated with new propellants that increased velocity without excessive pressure. Their 325-grain FTX is loaded to 2000 fps, yielding 2886 ft-lbs.
Today, the 1895 Marlin has been joined by newly manufactured Winchester 1886s, and Henry’s .45-70. Also, numerous big single-shots on old and new actions. Standard .45-70 loads continue with mild pressures, but there are ascending grades of .45-70, always available to handloaders. Hornady’s loading manual lists three sets of data for the .45-70: Trap Door, 1895 Marlin, and Ruger #1. Similarly, specialty ammo makers like Cor-Bon and Garrett offer .45-70 loads tailored to various action strengths.
: Boddington’s friend Bobby Dierks used his Henry .45-70 with Hornady FTX bullet and Leupold red-dot sight to take this awesome Kansas buck…at 200 yards. Tough shot with a .45-70 and/or a red dot, but obviously possible.
With heavy loads in strong actions, the .45-70 transcends the big woods cartridge it was long considered, to a serious thumper adequate for the biggest bears and baddest Cape buffaloes.
Part of this ammo revolution, and the .45-70’s resurgence, is based on the popularity of the “guide gun.” Whether Henry, Marlin, or Winchester ’86, the guide gun is simply a big lever-action somewhat updated. Usually with shorter barrel, perhaps a rail mount with ghost-ring aperture, rust-proof finish, laminate or synthetic stock.
The first “guide gun” I ever saw (before I heard the term) was a lovely Marlin .45-70 by Idaho custom maker Jim Brockman. Neither rail mounts nor Cerakote existed, but this rifle had it all: Matte metal, flat black stock. Three sight options: Detachable forward-mounted Long Eye Relief scope on the barrel and detachable 1.75-5x20mm scope on the receiver, rear receiver base also housing an aperture. Deadly accurate, this rifle was far ahead of its time. Wish I’d bought it.
: A fine Texas whitetail, taken with the Ruger/Marlin 1895 .45-70 using 325-grain Hornady FTX. We could agree that the .45-70 is more powerful than needed, but it drops deer with authority, little tracking required.
I didn’t, but I have a long history with the .45-70. The first animal I took with it was a big Arizona mountain lion in 1979. Not with a rifle, but with a JD Jones .45-70 barrel on a T/C Contender. In a handgun, the .45-70 is all the fun anyone needs!
Years later, I took a massive bison bull with a Wesson & Harrington break-open single-shot. I used .45-70 cases loaded to .45-90 specs, using 415-grain hard-case bullets. They exited the far side. A big bison is 25 percent larger than a Cape buffalo, so I know, unequivocally, that a .45-70 with good loads is adequate for African buffalo. In between, and still, a lot of pig hunting and close-range deer hunting with .45-70s, much of it preceding the “guide gun” phenomenon.
The lever-action is uniquely American, so “guide gun” is generally interpreted in Noth American context: A rifle a guide carries for in extremis use when hunting big bears. The concept is seductive, and big lever-actions became popular. Toward the tail end, Marlin was offering the 1895 .45-70 in many configurations. Despite parent company Remington’s impending doom, they were selling all they could make.
On the bench with one of the first Ruger/Marlin 1895s in .45-70. In stainless steel with laminate stock, this rifle had a wonderfully smooth action and produced near-MOA groups at 100 yards.
Ruger acquired Marlin from the ashes and tooled up to make lever-actions. I assumed they would start with a .30-30, but the first Ruger Marlin was a short-barreled 1895 .45-70 in stainless and synthetic. “Why” is simple: In latter Remington/Marlin production, .45-70s outsold .30-30s two to one. Good on the old warhorse .45-70!
The problem with the guide gun concept: Few of us hunt big bears or guide in big bear country, and the purposes aren’t the same. A bear guide should carry a fast-handling, powerful repeater. A bear hunter must carry a rifle that will stop a bear, also has adequate range. With proper loads, the .45-70 is powerful enough. On the latter count, I’m not convinced.
45-70 Group: Although at its best for short-range use, the .45-70 is often exceptionally accurate. This is a latter-production Remington/Marlin in “guide gun” configuration, fitted with an Aimpoint red-dot sight.
A young friend had a chance to go on an Alaskan brown bear hunt. He considered a lever-action .45-70. I talked him out of it. A 200-yard shot would be possible, but difficult. He chose a scoped bolt-action, got a nice bear. I hunted brown bear in Alaska last fall, never got a shot. Going again this spring. I have a Ruger/Marlin 1895 .45-70. Wonderfully accurate, wears a good scope. Love to take a big bear with that rifle, but I’m not taking it. Too costly a hunt to take chances! Last fall, I carried an accurate, well-scoped .338, same gun this spring. If my one chance is past 200 yards I can take it with confidence. Possible with a .45-70, but risky.
Co bison 45-70: This huge bison bull was taken with a Wesson & Harrington break-open single-shot .45-70. Hard cast bullets loaded to .45-90 specs gave through-and-through penetration, convincing Boddington the .45-70 is fully adequate for large bovines…with the right loads.
It’s not that the .45-70 isn’t capable of extreme accuracy or long-range shooting. Rather, its arcing trajectory makes longer shots difficult. And although big bullets always hit hard, they lose energy fast. I’d hunt Cape buffalo with a .45-70 before I’d take it for a big bear. I know I’m not going to shoot a buffalo past 100 yards. On a bear hunt, likely just one chance. I want to be certain I can take that shot with confidence.
So, whether you call it a guide gun or just a big lever-action, I see the grand old .45-70 as ideal for situations where you know the shot will be close. Perfect for pigs, awesome for black bear over bait or with hounds. Ideal for thick cover whitetail hunting. Overgunned, maybe, but not much tracking!
45-70 recoil: This Remington-production Marlin .45-70 “guide gun” is caught in peak recoil. Although more of a hard push than a sharp blow, the .45-70 is a powerful cartridge generating significant recoil, especially off the bench.
Let’s be fair: With modern loads and optical sights, the .45-70 is not a bayonet-range rifle. Couple seasons back my friend Bobby Dierks had a big Kansas buck up on an opposite ridge. He had his Henry .45-70 with Leupold red-dot sight, figured about 200 yards. He held the dot on the backline and dropped the buck. Fine shot with a .45-70…and with a red dot. Also, a great buck, entered into Boone and Crockett’s records at 173 typical. Regardless of game, circumstance, or load, the .45-70 is slow and its bullets drop quickly…but hit hard when they get there.
A cartridge “belt” is a narrow ridge of case material around the cartridge base, quickly stepping down to the actual case diameter. Throughout the 20th Century most cartridge dubbed “magnum” wore belts, so we came to accept that a belted cartridge was bigger, faster, more powerful.
New cartridges versus belted magnums.
By
Craig Boddington
A cartridge “belt” is a narrow ridge of case material around the cartridge base, quickly stepping down to the actual case diameter. Throughout the 20th Century most cartridge dubbed “magnum” wore belts, so we came to accept that a belted cartridge was bigger, faster, more powerful.
338 brown bear: Donna Boddington used a Proof Research in.338 Win Mag to take this big brown bear on Admiratly Island. There are faster and perhaps more accurate .338-caliber cartridges, but the belted .338 Win mag is the most popular, most available, and offers great performance with moderate recoil.
Around the turn of the millennium, with the introduction of fast, fat-cased unbelted RUMs,, WSMs, and more, cartridge design—and our perceptions—shifted away from belted cases. This has continued, witness the Nosler cartridges, Hornady’s PRCs, and Winchester’s 6.8 Western.
The world’s last belted magnum appears to be the 6.5-.300 Weatherby Magnum, introduced in 2016. Since then, even Weatherby has shifted away from the belt, introducing their 6.5 RPM (Rebated Precision Magnum) in 2019, following up with their .338 RPM in 2022. A rebated rim means that the rim is of smaller diameter than the base, allowing a rifle to house a fatter cartridge. Not a new concept. The first rebated rim cartridge was the .425 Westley Richards, introduced in 1908. Best-known is probably 1963’s .284 Winchester, parent case for the 6.5-.284 Norma, and the Weatherby’s RPMs.
264 mule deer: A fine Wyoming mule deer, taken at sunset with a 140-grain bullet from a .264 Win Mag. Though no longer popular, the .264 is still an effective hunting cartridge…and Boddington’s .264 shoots extremely well.
As with bottleneck cartridges with full-diameter rims, most rebated rim cartridges headspace on the shoulder. A headspace index is a critical feature to all cartridge design. Headspace, defined, “is the distance measured from a closed chamber’s breech face to the chamber feature that limits the insertion depth of a cartridge placed in it.” There are multiple ways to skin this cat, but all metallic cartridges have a headspace index mated to chamber dimensions.
6.5 lineup: Left to right: .274 Win Mag, 6.5-284 Norma, 6.5 PRC, 6.5 RPM, These four 6.5mm cartridges are identical in velocity and performance on game. Boddington would have one of them, but he has an accurate .264 he’s unwilling to abandon
Simplest is an exposed rim, mated to a recess at the beginning of the chamber. In the blackpowder era, almost all cartridges were rimmed, perfect for single-shots, fine for tubular magazines. Problematic for box magazines because the rims must be stacked to preclude jamming. There were effective box-magazine rifles for rimmed cartridges, but Peter Paul Mauser’s rimless cartridge proved a better mousetrap, headspacing on the cartridge shoulder. Obviously, the chamber must be cut right to match the case, and the cartridge must be manufactured to proper dimensions. Both were possible in the latter 19th Century, so shoulder headspacing became common and is considered more precise.
Let’s return to the belt. The first belted cartridge was Holland & Holland’s .400/.375 Belted Nitro Express, introduced in 1905, headspacing on the belt, with matching chamber recess The mild.400/.375 didn’t succeed. H&H tried again in 1912 with their .375 H&H Magnum. Its gentle shoulder was inadequate as a headspace index, so the belt was retained. Versatile as well as powerful the .375 H&H became a world standard. In 1925 H&H necked the case down to create the cartridge we know as the .300 H&H Magnum, headspacing on the belt because of its tapered shoulder.
: On the bench with an early 7mm PRC. Intrigued by its performance with heavy bullets, Boddington bought this Mossberg Patriot in 7 PRC
Since then, most belted magnums have used the .375 or .300 H&H case. The primary exceptions are Weatherby’s family of big cartridges based on the .378 case; and Weatherby’s two smallest magnums, the .224 and .240.
“Magnum” comes from a French word for an extra-large bottle of champagne. The British started using it in the blackpowder era for extra-large cases. Over time, “magnum” became synonymous with “faster and more powerful.” And, until the RUMs and WSMs, “magnum” was inextricably linked to a belted case.
Belted cartridges with defined shoulders don’t need the belt for headspacing, as long proven by our too-many unbelted “magnums.” Over time, the “magnum” suffix was clearly over-used. Enough turn-of-millennium unbelted magnums failed that today, manufacturers seem reluctant to use the word. Make no mistake: The Nosler cartridges and the PRCs are “magnums” in every sense we know, with or without belt or suffix.
375 Ruger LDE: Boddington’s favorite African animal is this excellent Lord Derby’s giant eland, taken in northern Cameroon with a .375 Ruger. An excellent cartridge in all ways, it’s unlikely to ever be as available or popular as the .375 H&H.
Not all belted magnums have succeeded. H&H’s .240, .244, and .275 belted magnums are nearly unknown. Neither the .308 nor .358 Norma Magnums ever caught on. Some of Weatherby’s belted magnums have achieve widespread popularity; others have remained primarily proprietary to Weatherby. Remington’s 6.5, 8mm and .350 Rem Mags languish.
Winchester’s 1958 .264 Win Mag was briefly popular, then nearly killed by the more versatile 7mm Rem Mag, introduced in 1962. I still have a .264. Velocity is identical to the 6.5 PRC. Because my .264 has an exceptional barrel, I’ll pit it against any 6.5 PRC for groups.If I wanted a fast 6.5mm with more versatility than the 6.5 Creedmoor, I’d get a PRC, maybe a 6.5-.284, maybe a 6.5 RPM. With almost no new platforms and limited ammo, I can’t recommend a .264 today…unless it was a great deal. For me, I have oceans of .264 brass and good handload recipes. Can’t see duplicating its performance and creating a whole new supply chain issue.
300 Win Mag groups: Boddington’s Jarrett .300 Win Mag groups well with a variety of both factory and handloads. He likes the new unbelted fast .30s just fine, but is satisfied with the performance he already has
Okay, my beloved .264 is history. However, several tried-and-true belted magnums remain worldwide standards: 7mm Rem Mag; .300 Win and .300 Wby Mag; .338 Win Mag; .375 H&H. All are widely loaded and chambered by most manufacturers. The 7mm Rem Mag was the world’s most popular magnum. The .300 Win Mag now occupies that spot, with the7mm Rem Mag still in second place.
In each bullet diameter, there are newer cartridges with modern (unbelted) cases that are at least as fast or faster. In 7mm: 7mm PRC, 28 Nosler, 7mm RUM. In .30: .300 PRC, .30 Nosler, .300 RUM, plus the belted .30-378 Wby. In .338, .338 RPM, .33 Nosler, .338 RUM, and .338 Lapua, plus belted .340 and .338-.378 Wby Mags. In .375, .375 Ruger and .375 RUM, plus belted .375 and .378 Wby Mags.
300 Wby Mag: Boddington has done most of his mountain hunting, especially in Asia’s big mountains, with various .300 Wby Mag rifles. This big Altai argali was taken in Mongolia with a .300 Wby Mag barrel on a Blaser R8
Newer cartridges with fatter, more efficient unbelted cases, are touted as being more accurate. Maybe, but in my experience quality of barrel, sound bedding and assembly, and quality of ammunition are more important to accuracy than case design.
Whether chambered to old belted or new unbelted cartridges, a good rifle should shoot well. The newest cartridges have an advantage in that they are, at least initially, offered in the best loads featuring the most accurate modern bullets. Hornady’s Precision Hunter line (PRCs) is awesome stuff and there are no flies on Nosler or Weatherby-branded ammo.
Boddington is not anti-magnification. Without question, high magnification makes
shooting tight groups easier. These were shot with a Sabatti Saphire .300 Win Mag, topped with
a Vector Optics Continental 3-18x50mm scope.
Regardless how good the ammo, a factory load is just one assemblage of components. No predicting what load a given rifle might shoot best. The more loads available to try, the better the odds of finding extra-good results. So, cartridge popularity is a virtue, not a sin. Handloaders can experiment endlessly. Factory load shooters should think about cartridges with limited choices.
New cartridges aren’t all about accuracy. A lot of our new cartridges are designed to be mated with faster-twist barrels intended to stabilize the longer, heavier, super-aerodynamic new bullets. Depends on what you intend to do, just don’t forget that heavier bullets and faster cartridges produce more recoil.
Me, I haven’t jumped heavily into the new cartridges. I concede they are “better,” but I’m neither a competitive nor extreme range shooter. How much better do I need? M trusty .264 is the primary reason I don’t have a 6.5 PRC.
7mm is a different story. I used to hunt extensively with the 7mm Rem Mag. Haven’t had one for years. The 7 Rem Mag’s traditional rifling twist was 1:925. Maxes out at about 175 grains, but when I was using that cartridge, I never shot bullets that heavy. I’m fascinated by the heavier 7mm bullets, so I bought a 7 PRC. So far, accuracy is adequate, not impressive; hope the loading bench makes it better.
I’m more of a .30-caliber guy. Most of my mountain hunting is behind me, much of it done with .300 Wby Mag and, more recently, .300 Win Mag. If I were to start over, I’d get one of the modern cartridges in a fast-twist barrel that would stabilize aerodynamic 220 and 225-grain bullets. Since it’s too late to start over, I’m good with my fast .30s in old, belted magnums…with lots of loads to play with.
In .33, I tried both the .340 Wby Mag and .338 RUM. Awesome performance, too much recoil. I retreated to the old standby .338 Win Mag, fast enough, plenty of power, acceptable recoil.
: Donna and Craig Boddington took these Mozambique Cape buffalo bulls from the same herd within a few seconds. Donna used a Blaser R8, Craig a CZ 550, both in .375 H&H. Total three shots fired. Since 1912, the .375 H&H has been plenty of gun for buffalo.
Similar story in .375. I used both the .375 Wby Mag and .375 RUM. Effective, but recoil too unpleasant. I have also used the .375 Ruger extensively, have both .375 Ruger and .375 H&H rifles. I’ll argue all day long that the .375 Ruger is a “better” cartridge than the .375 H&H: More efficient, fits into a lighter, more compact action. It is also faster and delivers more energy, but not by such a margin that recoil goes off the page. As large-caliber cartridges go, the .375 Ruger is popular, but it will never encroach on the .375 H&H’s worldwide availability.
New cartridges are always fun, may give a bit extra, but long-trusted cartridges still get the job done. Just think about it before you get rid of a traditional belted cartridge in favor of something new. Especially, consider what you intend to do, and how much popularity and resultant availability mean to you.
Yes, that title will upset some folks. Funny thing about the .25-caliber cartridges, bullet diameter .257-inch: Those who love ‘em tend to be passionate about their “quarter-bores.”. Those who don’t love .25s probably don’t hate them, just ignore them.
This big feral hog dropped in its tracks to a single 100-grain Interlock from a Savage 1899 in .250 Savage. The old .250 Savage isn’t fast, but it’s as effective on deer-sized game today as it was a century ago.
The .25-caliber is a uniquely American bullet diameter, rarely seen in Europe, equally uncommon in Africa. I’m told the .25-06 has some following in South Africa, but I’ve rarely seen a .25 in use on safari.
Over here, the quarter-bores have a rich history, going back to the dawn of smokeless powder. The .25-20 was created by necking down the .32-20 case to .25-caliber, first by Marlin, then by Winchester, and chambered in their popular 1892 lever-action. Initially loaded with blackpowder, the .25-20 quickly transitioned to smokeless. Although occasionally used for deer, the little .25-20 was a common small game and varmint cartridge, popular among trappers.
On a Kansas deer stand with a Winchester M94 .25-35, made in 1906. Because of iron sights, Boddington is careful which stands he chooses, but he does a “sit” or two with this rifle most deer seasons.
Winchester’s .25-35 was the first .25 designed for smokeless powder. The .25-35 and .30-30 use the parent same case, and were introduced together in 1895, so were the first sporting cartridges designed for smokeless propellent. Although hampered by round-nose bullets in tubular magazines, the .25-35 shoots flatter than the .30-30 with a less recoil. The .25-35 was a common alternative to .30-30, plenty of gun for deer-sized game. Jack O’Connor’s outfitter in Sonora in the 1930s, Charlie Ren, used nothing but a Savage 1899 in .25-35. O’Connor famously quoted Ren as saying it was “all he needed.” Lord knows how much game that rifle accounted for.
In 1915, Arthur Savage engaged early cartridge genius Charles Newton to develop a high-velocity cartridge for his lever-action. Newton’s project for Savage resulted in the .250-3000 (.250 Savage), the first commercial cartridge to break 3000 feet per second. The Savage lever-action was stronger than the Winchester, and its box magazine could use sharp-pointed bullets. The .250 Savage was popular for decades…and a real thorn in Winchester’s side.
Gunwriter Gary Sitton was another huge .25-06 fan. He used his Dakota M10 .25-06 to take this fine buck on John Wootters’ South Texas ranch, “Los Cuernos.”
In 1920, Savage introduced the M20. Essentially a scaled-down Springfield action, it was not only America’s first commercial bolt-action; it was the world’s first short bolt-action, sized specifically to the .250 Savage case. In our Kansas deer season just past, Ryan Paul brought a cherry M20 and shot does with it, first M20 I’ve ever seen in the field.
The only way the .250 Savage could reach 3000 fps was with its original light-for-caliber 87-grain bullet. 1915 expanding bullets worked when they worked, but most hunters learned that the .250 Savage performed better with 100-grain bullets at about 2800 fps.
Wyoming gunwriter Bob Milek in the field with one of his beloved .25s. Milek used both the .257 Roberts and .25-06 for game up to elk. Boddington doesn’t believe the .25’s have enough bullet weight or frontal area for larger game, but with proper shot placement, they surely work.
Gunwriter Ned Roberts necked the 7×57 case down to .25-caliber, creating the .257 Roberts, adopted by Remington in 1934. Its longer case enabled heavier bullets at higher velocity than possible with the .250 Savage. Until the .243 came along, the .257 Roberts was the standard “crossover” varmint/big game cartridge. Although rarely chambered in new rifles today, it was extremely popular, and remains an important cartridge.
The .25-06 was developed at Frankford Arsenal during WWI as a military experiment. After the war, it remained a common and popular non-standard wildcat. Amazing to me none of the majors picked it up sooner, but it wasn’t adopted as a commercial cartridge until 1969, as the .25-06 Remington. To this day, the .25-06 is the most popular .25-caliber. With heavier bullets, it is fast, flat-shooting, powerful, and awesome on deer-sized game. With lighter bullets, the .25-06 is probably the largest and most powerful cartridge that could sensibly be used for varminting.
Boddington used his Dakota .257 Roberts with 117-grain SST to take this weird Kansas “management” buck. The buck went down so fast and hard it seemed to bounce.
The .257 Weatherby Magnum was one of Roy Weatherby’s original cartridges, introduced in 1944, based on a necked down and shortened .300 H&H case. It is one of the fastest and flattest-shooting of all commercial cartridges and was Roy’s personal favorite. It’s not especially popular; a limitation is that it has remained a Weatherby proprietary, thus limited sources.
In recent years there have been few new .25-caliber cartridges. An exception was the short-lived .25 WSSM. Great little fireplug of a cartridge, about the same performance as the .25-06, yet from a much shorter case, fitting into short actions. Several of the short, fat magnums introduced at the turn of the millennium have fallen by the wayside. Mostly, I put this down to “too many, too fast.” Too many new cartridges for the market (us) to accept. The “super short” magnums were so short that feeding problems occurred in some platforms.
For the record, I’m not a huge .25-caliber fan but I neither hate them nor ignore them. I have a long history with .25s. In the early ‘70s, on a cougar hunt, the houndsman handed me a Colt Lightning slide-action .25-20. Since then, I’ve hunted with all of them, even tried the .25 WSSM when it was new. I had a super-accurate .25-06, used it a lot, have had a couple of .257 Weatherby Magnums. As a lever-action buff, I’ve had a succession of .250 Savage rifles, have a good one now, made in 1920. Also have a 1906 M94 in .25-35. My current favorite .25, however, is a Dakota M76 in .257 Roberts, accurate and sweet-shooting.
This blacktail was taken with a .257 Weatherby Magnum. By far the fastest commercial .25-caliber, the .257 Wby shoots flat and hits hard.
I admit that I’m not passionate about .25s, but friends that I’ve respected have been. Great gunwriter, friend, and mentor Bob Milek was a quarter-bore guy. He loved the .257 Roberts and .25-06 equally. Gary Sitton, one of our greatest gunwriting talents, was also a .25-06 guy. My longtime boss at Petersen’s HUNTING, Ken Elliott, was a .257 Weatherby Magnum guy, thought it was the cat’s pajamas. So did Robert E. “Pete” Petersen, founder of Petersen Publishing. Sadly, all these guys are gone. Scott Rupp, one of the best Editors I currently work for, is still with us. He’s a quarter-bore guy.
Tastes in cartridges are often somewhat reginal. Usually, this is driven by game hunted, and by local hunting conditions. Texas is the great stronghold of the .25-06. Hard to find a Texas deer camp where somebody isn’t toting a .25-06. Medium-sized deer, shots often on the longer side. More than that: A common landform there is long, open cuts between brushlines, the famous Texas senderos. Here’s the thing about hunting a sendero: They’re narrow with few reference points. When a buck steps out he may not stop for long. No time to mess with a rangefinder, quick look at antlers and shoot. A flat-shooting .25 is a near-perfect choice.
In 2023, Ryan Paul brought a Savage M20 to Kansas, first time Boddington has seen an M20 in the field. An aperture-sight rifle, Paul used it to take does, using a scoped rifle for his buck.
In Central California, we hunt small-bodied blacktail deer. The .25-06 is popular here today, but, historically, I think the .250 Savage was a top gun. I say this because, for years, it was easy to find Savage 99s in .250 on almost any used-gun rack. In the .250 Savage’s heyday, we didn’t yet have feral hogs, and in our tight canyons, shots on our blacktails are rarely long. The .250 Savage was an ideal choice.
For me, the .25s are excellent for pronghorns and deer-sized game, questionable for larger game. Others disagree. Bob Milek used his .257 Roberts or .25-06 for elk almost every year. Milek was a Wyoming resident, usually looking for a fat cow or young bull for the freezer, rarely seeking (or taking) mature bulls. In that context, fine. For all-around elk hunting, I draw the line. Can work just fine, with caution, but I don’t think the .25s offer either the bullet weight or frontal area for general use on game larger than deer.
A nice Central Coast blacktail, taken with a .25-06 on a Ruger M77 action. Accurate and flat-shooting, the .25-06 is the most popular .25-caliber cartridge, a great choice for deer-sized game.
If there’s a fly in the .25-caliber ointment, it’s a bullet problem. Like our traditional .270 cartridges, the .25s have always been considered hunting cartridges. Historically, there have been almost no match-grade bullets or loads in .25-caliber. Today, with the rage for range, little development of modern, low-drag .257 projectiles. As with older .270s, part of this is a rifling twist issue. Since the 1920s, standard rifling twist for .25-caliber cartridges has been 1:10, stabilizing bullets from about 70 to 120 grains. Maximum G1 Ballistic Coefficient (BC) for the most aerodynamic 120-grain .257 bullets is about .400. Not bad, but not in the same league as the modern low-drag bullets with BCs well over .600.
We need longer, heavier .257 bullets to get there, but our 1:10 barrels won’t stabilize them, and many of the actions on our .25-caliber rifles won’t house them. There are some options out there. Berger makes a 133-grain .257 bullet, and Hornady has a new 134-grain .257 ELD-Match with G1 BC of .645. Undoubtedly, these choices will grow. However, none of my .25s will stabilize these bullets. I’m not interested in rebarreling. Same story as my pet .270 Winchesters regarding the new, heavier .277 bullets.
Two different approaches to varmint rifles. Left, a Savage .22-250. Right, a .25-06 on a Ruger M77 action, both with adequate accuracy for any varminting. Boddington believes the .25-06 is the most powerful cartridge that makes sense for varminting.
Doesn’t matter to me. I’m not an extreme-range guy. My .25s shoot well enough and flat enough for my purposes. Happy to keep them in their box as awesome, light-recoiling choices for deer-sized game, at shooting distances I’m comfortable with.
In America, above .30-caliber, cartridge popularity drops like a thrown rock. This is as it should be. Little on this continent that can’t be done with a .30-caliber and good bullets. Millions of American deer hunters don’t even need a .30, filling their freezers and trophy walls just fine with lighter calibers.
Boddington and Jack Atcheson Jr. with a Montana mule deer taken with a .338 Win Mag. Atcheson is a huge .338 fan, rarely using any other cartridge…anywhere. For deer-sized game, Boddington usually uses lighter cartridges. But, as Atcheson says, the .338 “numbs them.”
Still, we do have larger game: Elk, moose, the big bears. Hunters who pursue them—and those who dream of such hunts—love to argue around the campfire about the best and most perfect cartridges. Calibers and cartridge choices are legion. I’ve had long affairs with 8mms, diameter .323. Few cartridges and, ultimately, not enough bullets. Friend and mentor Colonel Charles Askins was the ultimate 8mm guru. Askins begged for a 250-grain 8mm bullet, but 220 grains has been the limit. Whether .325 WSM, 8mm Remington Magnum (or one of Askins’ myriad 8mm wildcats), a fast 8mm with 220-grain bullet is a wonderful thumper on elk. However, in my opinion, available bullets aren’t heavy enough for the largest bears.
Pound for pound, Boddington doesn’t believe moose are as tough as elk, but moose are much bigger. This bullet was taken at about 300 yards with a .338 RUM, firing 250-grain Swift A-Frame.
I also love the .35s. There are bunches of older .35s: .35 Remington; .348, .358, .356 Winchester. Also new: .350 Legend and .360 Buckhammer. Great for black bears and feral hogs, but either marginal in power for larger game, or not enough velocity for versatility in open country. The .35 Whelen and .350 Rem Mag are almost there in both power and velocity. Wonderful for elk and moose, just a bit on the mild side for anything bigger. Oddly, there have been almost no fast .35s. The .358 Norma Magnum is rare; the .358 Alaskan (7mm STW necked up) never made it into factory form.
In October ’23 Boddington used a .338 Win Mag barrel on his Blaser R8 on a brown bear hunt on the Alaska Peninsula. Didn’t get a bear, but he was ready.
Tough to make a case for bigger. The 9.3mms (.366-inch) are popular in Europe, used for driven boar, also by Africa-bound Europeans as alternative to .375. The two most popular—the rimless 9.3×62 in bolt-actions and rimmed 9.3x74R in single-shots and doubles—are just slightly less powerful than the .375 H&H, so plenty for North America’s largest game…but maybe don’t shoot as flat as optimum for our conditions. The faster .370 Sako and 9.3×64 Brenneke are similar to the .375 H&H in bullet weight, velocity, energy, and trajectory. Like the .375s themselves, this means they are overpowered for almost everything in North America except our biggest bears.
I’ve used various 9.3s on African buffalo, and in North America for hogs and black bear. Over here, I’ve used .375s for elk and moose, and for big bears. Awesomely effective…but more powerful than absolutely necessary. Truth is, for North American hunters on home turf, there’s little justification for a 9.3mm, .375, or larger. Fun to own, limited utility.
Left to right .325 WSM, .8mm Rem Mag, .338 Win Mag, .338 RUM, .340 Wby Mag. As a group, the “medium magnums” are extremely effective on game larger than deer. Boddington has hunted with all these and more but believes the .338 Win Mag is the most useful: Fast enough, without excessive recoil, and available in the greatest variety of loads.
If you’re looking for a cartridge with more knockdown power for North America’s large—and largest—game, it seems to me the caliber to pick is .338. Bullet selection is rich, standard at about 180 to 250 grains. There are numerous good cartridges using this bullet diameter at various velocity levels, including: .338 Federal, .338 Marlin Express, .338-06, .338 Ruger Compact Magnum (RCM), .338 Weatherby Rebated Precision Magnum (RPM) .338 Winchester Magnum, .340 Weatherby Magnum, .338 Remington Ultra Magnum (RUM), .338 Lapua Magnum, and .338-378 Weatherby.
All are adequate for elk and moose, and all are fast enough for at least medium ranges. However, if we include the biggest bears—and want the utmost in versatility—then we probably want a cartridge with enough case capacity to propel heavy bullets at meaningful velocity. I think the place to start is in the middle of that cartridge list, with the .338 Winchester Magnum.
Boddington has found most .338s to be accurate and non-finicky. His .338 Win Mag barrel for the Blaser R8 is simply amazing, producing sub-MOA groups with 250-grain bullets
Winchester started their line of .30-06-length belted magnums in 1956 with the .458. In 1958 the family grew with two new cartridges in versions of their beloved Model 70 bolt-action: The .264 Win Mag in the “Westerner;” the .338 Win Mag in the “Alaskan.” The .338 Win Mag was intended for the largest Alaskan game, which includes elk, moose, and our biggest bears. Most common factory loads are 200, 225, and 250-grain bullets. Respectively, velocities are around 2950, 2800, and 2650 fps, all producing about 3900 ft-lbs of energy.
.33-caliber has deeper roots among British cartridges. The .333 Jeffery, available in both rimless and rimmed (.333 Flanged) versions, was loaded with 250 and 300-grain bullets. The .318 Westley Richards was more popular. Its designation comes from the inconsistent British convention of naming cartridges by the smaller land vice groove diameter: The .318 uses a .330-inch bullet, so also a .33. In the days before caliber minimums were instituted, both the .333 Jeffery and the .318 WR were used to take game up to elephant (with non-expanding solids). WDM “Karamoja” Bell, best known for preferring the .275 Rigby (7×57), wrote that his largest one-day bag of elephants was taken with a .318, using 250-grain solids.
PH Cliff Walker and Boddington with a Lichtenstein’s hartebeest, taken with a .338 RUM. Although not especially common in Africa, all the faster .338 cartridges are adequate for the full run of large African antelopes.
Gunwriter Elmer Keith (1899-1984) hailed from Idaho and hunted elk in black timber. He became a lifelong believer in larger calibers with long, heavy bullets. Working with Charles O’Neil and Don Hopkins, he used the .30-06 case and .333 Jeffery bullets to create the wildcat .333 OKH.
Winchester’s .338 used a literal .338-inch bullet. In 1902 Winchester introduced the .33 Winchester in their M1886 lever-action, using a 200-grain .338-inch bullet at 2200 fps. The .33 predated the British cartridges, but why Winchester chose the .338-inch diameter isn’t known. Although Winchester quit loading .33 Win in 1940, it’s natural that Winchester used the same diameter for their .338 Win Mag. All “.33s” that have followed, including Elmer Keith’s later wildcats, use .338-inch bullets.
The .264 and .338 Winchester Magnums were introduced together in 1958. The .264 debuted in a version of the Winchester Model 70 called “Westerner;” the .338 was brought out in an M70 dubbed “Alaskan.”
Like most new cartridges, the .338 got a lot of buzz, but initial sales were slow. Probably because the word spread about sharp recoil. Duh! Although the lighter bullets kick less, you cannot produce nearly 4000 ft-lbs of energy without recoil, and not everyone needs this level of power. Over time, those who do discovered the .338 is wonderfully effective on large game. Lighter cartridges work fine on elk, but elk are tough, and many hunters want more. The .338 has become a standard “big gun” for elk, excellent for moose, and a sensible, fully adequate minimum for our largest bears.
Although lighter cartridges certainly work, Boddington believes the several .33-caliber cartridges are ideal for elk. This Roosevelt elk was taken with a .338 Win Mag using a 210-grain Nosler Partition.
Let’s go back to that list of current .33-caliber cartridges. The .338 RCM and Weatherby’s new .338 RPM are ballistically about the same as the .338 Win Mag, with more modern case design: The short, fat, unbelted RCM is a short-action cartridge; the RPM is unbelted. Despite its out-of-fashion belted case, the primary advantage of the .338 Win Mag is its greater popularity, offering a wider selection of loads from more manufacturers.
The last four cartridges on that list–.340 Wby Mag, .338 RUM, .338 Lapua, and .338-.378 Wby Mag—all have greater case capacity and are considerably faster than the .338 Win Mag. Energy yields approach or exceed 5000 ft-lbs. Trajectories are flatter, thus extending effective range. These are valuable attributes, but it depends on what you need, and how much recoil you’re comfortable with. I haven’t spent much time with either the .338 Lapua or .338-.378 Wby Mag…and probably won’t. I used the .338 RUM when it was new, also did a lot of hunting with the .340 Wby Mag. Both were wonderfully effective, hard-hitting and flat shooting.
Donna Boddington used a Proof Research .338 Win Mag and a single 225-grain InterBond to take this big Alaskan brown bear on Admiralty Island.
I took the .340 to Africa a couple of times. I’m not especially sensitive to recoil, but that’s where I learned my limit. In the context of shooting plains game almost daily, I decided the .340 was more fun than needed. I circled back to the .338 Win Mag. It kicks, but I’m comfortable with that level of recoil. The faster .33s come back a bit too hard and too fast for my taste, especially on a sustained basis. Like everything else, they can be tamed with muzzle brakes. I prefer not to use brakes because of the blast and, anyway, I’m not an extreme-range shooter on game. The .338 Win Mag shoots flat enough for my purposes, with acceptable recoil.
A good black bear from southeast Alaska, taken with a Proof Research .338 Win Mag. There are many great cartridges for black bear, but the .338 is adequate for the largest bears that walk.
My old friend Jack Atcheson Jr. is a major .338 fan. Great sheep hunter and Montana elk hunter, he uses almost nothing else…all over the world. On deer-sized game the fast .33s speak with authority, but they are needlessly powerful. Trajectories are flat enough for great versatility, but I prefer lighter, faster cartridges for mountain game. For me, the .33s are fantastic for elk and moose, devastatingly effective on our largest black bears, and fully adequate for the largest bears. Perhaps oddly, I’ve used the .338 relatively little in Africa. Not sure why. It is unquestionably fully adequate for the full run of large plains game. I’ve often stated that a .338 matched up with a .416 makes the most perfect African battery.
For big bears, moose, and in Africa, I’ve usually loaded up with 250-grain bullets. It’s important to understand that the 250-grain .338 bullet has slightly higher Sectional Density (SD) than 300-grain .375 or 400-grain .416 bullets. So, if construction and velocity are similar, it will penetrate at least as well as these famous bullets. For elk and smaller game, I usually use lighter bullets from 200 to 225 grains, increasing velocity, flattening trajectory, and reducing recoil. Not everyone needs a .338, but if you want more power for larger game, I’m convinced a fast .33 is the way to go.
Like most kids, my first shooting was with a single-shot .22, but, absent a modern Kansas deer season, we were shotgunners, no need for centerfire rifles. Couple hundred miles southeast, Warsaw, Missouri, had a sign proclaiming it “Gunstock Capitol of the World,” home to both the E.C. Bishop and Reinhart Fajen gunstock companies. There, my Dad’s friend Jack Pohl, owner of Bishop’s, was an avid benchrest shooter, big-game hunter, and handloader.
As a youngster, Boddington did almost all of his hunting with handloads, secure in the belief he could build a better cartridge than he could buy. His first “good” mule deer was taken in 1978 with a Ruger .30-06 using 180-grain Nosler Partition and a near-max charge of IMR 4350. The shot was about 450 yards, a very long poke back then.
Mr. Pohl was enlisted to introduce us to the centerfire rifle world. I was probably 12. The deal: He’d take us to the range, and woodchuck shooting. As a graduation exercise, we’d join him on a pronghorn and deer hunt in Wyoming. Big stuff! First, I had to learn how to handload. We started on his bench, then got a basic setup in our basement. Dad knew how to supervise his young son, but I did all the loading. I loved it, spent countless hours with that green RCBS press. Sixty years later, it’s not my only press, but I still use it.
Back then, there were two primary rationales for handloading. First, save money. Second, more important: It was an article of faith that you could load better ammo than you could buy.
Going back 60 years, Boddington has spent countless enjoyable hours at the loading bench. This is his new bench with new Hornady tools, but he still has—and uses—a lot of the reloading equipment he’s had since he was a teenager.
Today, both arguments hold less water. Ammo was cheaper back then, so were the basic tools and components. Even then, you had to do a lot of shooting to amortize the equipment. Of course, handloading drives you to shoot more, not a bad thing. You must try this load and that and keep searching for a better combination.
Today, I’m shocked at the cost of factory ammo. However, reloading components and equipment have also gone up (like everything else). Buying in bulk, especially powder and primers, reduces the per-cartridge cost. Still, it takes a lot more shooting to break even.
This is Boddington’s lifetime-best group, .052-inch with an 8mm Remington Magnum and a carefully-worked up handload. Groups like this are uncommon with anything, but most attainable through careful, precise handloading.
I started handloading in the Sixties. By the Nineties, factory ammo was so good, and so varied, that it was no longer a given it could be beat…depending on your purpose, and how serious you are. For ultimate accuracy, such as benchrest, long-range, and precision shooting, carefully concocted handloads usually win.
No matter how good, any factory load is just one assemblage of the four components: Case, primer, propellent, projectile. Changing any of them can make a difference in any rifle. In handloading, you can vary all of them, almost endlessly. Different brands and strengths of primers. Even cases vary among the brands. When I was young, our primary choices in bullets were Hornady, Nosler, Sierra, and Speer. More brands today, more weights and shapes. Back then, we might have had two dozen propellants to choose from, including pistol, rifle, and shotgun powders. Today, into the hundreds, new ones all the time.
The .348 Winchester is one of Boddington’s favorites. Into the 1980s, components were relatively available with multiple choices. Today both ammo and .348-inch bullets are scarce; handloading is the only sensible option for uncommon cartridges.
I’ve always been a lazy handloader. My searches for perfect loads have rarely been exhaustive. I tend to use the cases I have (and, today, the primers I can get), and there are plenty of bullets and powders I’ve never tried. Still, I work up loads for my rifles. I experiment with different powders and bullets, varying charge weight and seating depth. As good as factory ammo is today, I can usually build a more accurate load than I can buy…if I care to try.
I don’t always try. Maximum accuracy isn’t always essential. I’m not a competitor, mostly a hunter, and some of my rifles, older lever-actions and double rifles, are specialized in purpose and limited in range. I can beat factory loads, but not by enough to increase performance.
This Uganda buffalo was taken with a .470 made in 1906, firing a handloaded 500-grain Hornady DGX-Bonded. Since volume is low, factory ammo is currently scarce for most big-bore cartridges.
By the Nineties, factory ammo had gotten so good, and the choices so varied, that I wasn’t loading much anymore. A few years later, not at all. For some years my loading gear was boxed up. Thank God, I kept it!
I restarted mostly because I missed my time at the bench. Cost and performance aside, my single greatest reason for handloading: It’s fun! It is a mindless exercise, except you must stay focused. Do that, inspect constantly, use common sense (and loading manuals), and you can’t get into too much trouble. The results are wonderfully satisfying. I get a huge kick out of shooting a nice, tight group. Even better when it’s a load I cooked up. As a hunter, I still get the same old thrill from taking an animal. Rifles matter to me, so it’s better with a special rifle. Better still with a load I’ve worked up for that rifle and hunt.
Son-in-law Brad Jannenga used Boddington’s Savage 99 in .300 Savage with handloaded Swift Scirocco to take this big Axis buck. Tens of thousands of .300 Savage rifles are still in use…but the majors haven’t done runs of ammo in several years. Handloading is the best answer for many older cartridges.
As we know, things have changed. I didn’t foresee the late-teens ammo shortages, and for sure I didn’t anticipate that nasty little virus. My loading bench kept me sane through the pandemic…and still keeps me in business. Supplies are getting better, but still aren’t right. I’ve been out of standard large rifle primers for months, using magnum primers and dropping the load a wee bit. For sure I can’t always find the exact bullet or propellent I want.
Fortunately, there are lots of choices, usually something out there will work. Just the other day, I shopped this site, found two of three propellant I needed (not bad), and bullets I’d been looking for. Things are getting better…depending on what you shoot. On the shortages: I am not a conspiracy theorist. I put it down to increased demand. Millions of new shooters buying ammo, and that’s a good thing. Also, panic buying and hoarding. I believe the ammo makers are doing their best to catch up. However, it costs gazillions and takes time to gear up for unprecedented demand. This must be done with caution…because peak demand has already subsided.
Boddington isn’t a blackpowder guy but needed to work up loads for his son-in-law’s .500 Black Powder Express, made in 1885. This hog was taken with a 440-grain Hawk bullet with smokeless equivalent load…and lots of Dacron pillow stuffing to keep the powder down on the primer.
The biggest problem for many of us: The catchup process has focused on cartridges with the highest demand and deepest backorders. Outlets are awash in .223, 6.5 Creedmoor, and .308 ammo. I shoot them, but I also shoot older cartridges. Plenty rifles still out there, but factory ammo is scarce because the majors haven’t done runs in years: .250 and .300 Savage, .257 Roberts, .303 British, .348 Winchester.
Handloading has been my salvation. I also use several large-caliber cartridges: .405 Winchester, .450/.400-3”, .450 and .470 Nitro Express. Now we’re down to limited suppliers…and few or no recent runs. PHs all over Africa are dying for ammo (almost literally). So am I. I have great faith in my handloads, no qualms about hunting with them. Except, on dangerous game I prefer to use fresh factory ammo. If something bad happens, just as soon the post-mortem does not suggest it was my handload’s fault. In ’21 I wanted to use a new-to-me but very old .470 on a buffalo hunt in Uganda. Couldn’t find any fresh .470 factory ammo to save my soul. No problem, I’ve had dies since 1980. Getting a double rifle’s barrels to shoot together can be tricky. Got lucky, this rifle responded to a standard recipe. Took two nice bulls with my handloads, great performance and extra fun.
With double rifles, the challenge is getting the barrels to group together. This 1895 double in .303 British has been a treat. Regulated with 215-grain bullets, it also prints well with lighter bullets at the same velocity. These pairs represent changes in sight elevation.
As a lazy handloader, I’ve generally resisted complex projects. This is my primary reason for avoiding wildcat or non-standard cartridges. Slothfulness aside, I think we have enough standard factory cartridges to choose from. However, with shortages and interrupted supplies, sometimes handloading is the only solution. Gotta have dies, but even with non-standard cartridges, custom dies can be made (extra-simple if you have fired cases from the chamber)
Again, I try to stay out of this game, but recently I’ve had some unusual handloading projects. I bought a .50-115 Sharps from a dying friend. No factory ammo for that one, but the rifle came with cases, dies, and a bullet mold. That one has been fun. I’m not a blackpowder guy, nor a cast bullet guy, but it shoots well with a 515-grain cast bullet and Tin Star, a blackpowder-equivalent propellent that I’d never even heard of before.
The .348 Winchester is one of Boddington’s favorites. Into the 1980s, components were relatively available with multiple choices. Today both ammo and .348-inch bullets are scarce; handloading is the only sensible option for uncommon cartridges.
Although scarce today, the .303 British isn’t rare. My rifle is a very old double, regulated for the old 215-grain bullets. Woodleigh in Australia still made them, but their factory had a major fire. I found a supply, am hoarding them. Took some work, but I have loads that regulate well with 150 and 174-grain Hornady as well as the 215-grain Woodleigh. In May, I shot a nice Alberta black bear with the old double and 215-grain handloads. Awesome penetration, sort of double the fun!
A nice Alberta bear, taken with double in .303 British, firing a handloaded 215-grain Woodleigh. This was the original .303 bullet weight, so this hundred-year-old rifle was regulated with that bullet weight.
The biggest recent project: My son-in-law bought an 1885 exposed hammer double in .500 Black Powder Express (BPE). Of course, no ammo, but there are bullets, and case dimensions are the same as for .500 Nitro Express. This one has been a nightmare, but we’ve got both barrels shooting together with a mild charge of smokeless IMR 4198 and about 15 grains of Dacron pillow stuffing on top of the powder. Between poor light and my fading eyes, it took several outings, but I finally pounded a wild hog with it. If there’s an ammo problem, handloading can almost always solve it…and it’s fun!
A writer friend was in black bear camp this past spring, shooting a .30-06. At the sight-in range, younger hunters gathered to admire his rifle. They’d heard of the .30-06…insisted they’d never seen one.
By about 1930 the .30-06 reigned as America’s most popular hunting cartridge, holding this position for at least 40 years. Times change, but I’m shocked there are grownup hunters who have never seen or given passing consideration to the .30-06.
46 years after his first safari, Boddington still believes the .30-06 is among the best and most versatile choices for Africa’s non-dangerous game. This fine waterbuck was taken in 2019, using a left-hand Ruger M77 with 180-grain Hornady Interlock.
In 1903 the United States military adopted the Springfield bolt-action rifle, mated with a rimless bottleneck cartridge firing a .30-caliber (.308-inch bullet). Rifle and cartridge were so close to Peter Paul Mauser’s designs that Uncle Sam paid Mauser a royalty until WWI. The original 1903 cartridge used a 220-grain round-nose bullet. In 1906 the case was modified slightly, the bullet changed to a lighter spitzer with greatly improved aerodynamics. The new cartridge was called “Caliber .30 US Government Model of 1906.” We soon shortened that to .30-06.
The first sporting use of the .30-06 doesn’t seem recorded. Well-known is that Theodore Roosevelt swore by his Springfield throughout his epic nine-month 1909 safari. At that time the lever-action was America’s most popular sporting rifle. There were no domestic civilian bolt-actions at all until 1920.
.30-06 velocities vary considerably among manufacturers. With 165-grain bullet, Hornady’s Superformance load yielded 3016 fps…that’s edging into .300 magnum velocity.
The Savage M20 was America’s first bolt-action sporter, Sort of a mini-Springfield, it was sized for the short .250 and .300 Savage cartridges and could not house the .30-06. The first American sporter that could was Remington’s M30 in 1921, based on the big 1917 US Enfield action. Winchester followed in 1925 with the M54, forerunner to the M70 (1936).
Shortage of commercial rifles didn’t deter the .30-06. Surplus US Enfields and Springfields were cheap and available. The supply from both world wars lasted through the Sixties. My own first centerfire, purchased in 1964, was a surplus ‘03 Springfield. I think it cost $39.95. I didn’t hunt with it until years later, but I shot it a lot, and lovingly “sporterized” it.
We hear about new cartridges being inherently accurate, but don’t sell the ’06 short. This lightweight Kimber Terminal Ascent produced sub-MOA groups right out of the box with the first load tried, Federal 180-grain Trophy Tip bonded bullet.
Starting in 1925, the flatter-shooting, softer-kicking .270 gave the .30-06 competition but never overtook it. Even Jack O’Connor, high priest of the .270, conceded that the .30-06 was more versatile. The first magnum craze of the Fifties and Sixties eroded the .30-06. I bought into that stuff; I had a .264 and a .300 Winchester Magnum before I hunted with a .30-06.
Although she later switched to a .270, Donna Boddington did most of her early hunting with a left-hand Ruger M77 .30-06. She used a 180-grain Hornady Interlock to drop this excellent Mozambique sable with one shot at sundown.
I read my Roosevelt, and my Hemingway, and my Ruark, so when planning my first African hunt I knew I had to have a .30-06. I trotted down to the PX and bought a Ruger M77 and worked up handloads with 180-grain Nosler Partitions. Even though I’d been a confirmed magnum maniac (“magniac”), I was amazed at how well the .30-06 performed. All ranges, all sizes of plains game. Became, and have remained, a .30-06 fan.
The flood of unbelted magnums at the turn of the millennium gave us new choices. Recent cartridges designed for maximum efficiency (PRCs, Noslers, Westerns) give us more options. Today we have plenty cartridges to choose from. It’s easy to overlook the .30-06.
The .30-06 probably isn’t an ideal mountain cartridge, but it shoots flat enough. Grancel Fitz took his first sheep, a Dall sheep in Alaska, in 1935 with his Griffin & Howe Springfield. 20 years later, he was the first person to take all varieties of North American big game…all with this same .30-06.
Old, but not tired. The .30-06 is a powerhouse. Standard issue for our forces for 50 years, the .30-06 is the most powerful cartridge adopted by a major military. Not as fast as our many magnums, it is not slow. Standard velocity for a 180-grain bullet is 2700 fps. In perspective: The same speed as the 6.5mm Creedmoor…with a 140-grain bullet. With 180-grain bullet, the .30-06 offers 28 percent more bullet weight…with .044-inch more frontal area. There is no comparison in hitting power.
Wife Donna did her early hunting with a Ruger M77 .30-06. Not the same one. I was doing a lot of hunting with a left-hand action M77 .30-06. Also a lefty, she’s shorter, so I took a sliver off the butt and reset the recoil pad so we could both shoot it comfortably.
Sadly, not all new rifles are chambered to .30-06. This is Chapuis’ new ROLS straight-pull, made in France…with .30-06 among its many chamberings. So far, out of the box accuracy is about one MOA…not unusual for good rifles in .30-06.
Now, let’s be clear. The .30-06 is not a low-recoil option. Generations of recruits complained about the brutal recoil. They were not wrong. Donna is one of those people who is uniquely impervious to recoil. In general, I don’t recommend the .30-06 for youngsters, for women of smaller stature, or for anyone with aversion to recoil.
To this day, the (nominally) 2.5-inch of the .30-06 defines “standard-length” actions and cartridges. Factory cartridges based on the ’06 case include, left to right: .30-06, .270 Win, .280 Rem, .25-06, .35 Whelen, .370 Federal, .280 AI. Boddington believes the .30-06 is still the most versatile of all.
The .30-06 is a big gun, needlessly powerful for any deer hunting. It is a far better elk cartridge than deer cartridge! I still have magniac tendencies. I see the medium magnums, typified by the .338 Winchester Magnum, as the most ideal elk cartridges. Yes, but the .30-06 is plenty of gun for any elk, especially with today’s great bullets. I’ve taken as many bull elk with the .30-06 as with magnums. None have gone farther, most down in their tracks. Because of heavier bullets with more frontal area, I think the .30-06 is more effective on elk than any of the 7mms.
One of the advantages to the .30-06 is lots of loads…and lots of handload recipes. This Savage 110 .30-06 grouped variously with different loads…and then shot quarter-inch groups (bottom center) with Federal factory with 180-grain Barnes.
The .30-06’s strongest suit is versatility. Awesome for larger game, such as elk and moose. I still can’t think of anything better for the full run of non-dangerous African game. The .30-06 kicks but lacks the bone-jarring recoil velocity of the fast magnums…and it works.
Versatility isn’t just about size of animals. Today’s newest cartridges use faster rifling twists with extra-heavy bullets with super aerodynamics. The .30-06’s traditional 1:10 twist stabilizes bullets from 150 to 220 grains. How much versatility do you need? For deer, a 150-grain bullet zips along at 3000 fps. For elk, and for Africa’s variety, I’ve always been a 180-grain bullet guy. I’m not keen on using the .30-06 for big bears, but more grizzlies and brown bears have fallen to the .30-06 than all the rest put together. Old-timers relied on the long, heavy 220-grain slug, which can be loaded to 2550 fps, credible velocity for such weight, offering wonderful penetration. I also don’t recommend the .30-06 for extra-large beasts. However, in the days before minimum legal calibers, the .30-06 with 220-grain solids had a great reputation for reliable penetration all the way up to elephant.
The .30-06 is probably needlessly powerful for deer…and also dramatically effective. This big Colorado buck was dropped in its tracks by a single 180-grain Fusion bullet from an ’06 made by Kenny Jarrett.
Maybe it’s also not the best choice for mountain game. As with deer, .30-caliber bullet weight and power aren’t essential for sheep and goats. I’ve taken both with the .30-06, but I’ve usually chosen cartridges that shoot flatter. Not because I needed them, but because they seemed a better “fit.” Once you get to the point where you must either hold over or start dialing your turret for range, trajectory is just a number. Know the number and you can solve the problem.
I’ve done a lot of 1000-yard shooting on steel with various .30-06 rifles and loads…as have long-range competitors for 120 years. Once you start adjusting, a few more clicks is a matter of knowing how many. I’m not an extreme range shooter on game. If I were, then there are better tools. However, because that’s what I was carrying—and because I knew the trajectory—I’ve made some of my longer shots in the field with the .30-06.
Boddington believes the .30-06 is a wonderful elk cartridge…and better for elk than deer. This bull dropped in its tracks to a single 180-grain Barnes TSX at about 150 yards.
Many of our newer cartridges offer great versatility on game, at varying levels of recoil, and are often touted for accuracy. Cartridge design matters, but rifle, barrel, and ammo are more important. It’s an article of faith that the .308, with its shorter, more efficient case, is more accurate. Maybe, but the margin is slim. I’ve rarely seen accuracy problems in a .30-06 rifle. With higher velocity, the .30-06 is more powerful, thus more versatile.
So many choices, so many conflicting and confusing cartridges. Here’s one good reason why the .30-06 may be worth your consideration. Availability. Everybody loads .30-06. It is no longer our most popular centerfire…but it’s still in the top handful. There are hundreds of factory loads, from all manufacturers, throughout the world…offered with just about any bullet you can think of. No, these days, we can’t get them all. But the .30-06 is not a one-company wonder, as new cartridges must be until they catch on. For handloaders, we have a century of loading data to fall back on. Can’t get this powder or that bullet? Plenty of choices.
Willem van Dyk, trackers, and Boddington with a big fringe-eared oryx, taken in Kenya in 1977 on Boddington’s first African hunt. This was the first time Boddington hunted with the .30-06; impressive performance made him a lifelong fan.
Just yesterday, I went to the range with a new Chapuis ROLS, a fine, state-of-the-art straight-pull rifle. Made in France…chambered to .30-06. Finding the best load for this rifle is still a work in progress, but the loads I grabbed randomly from my garage grouped within one MOA. That’s performance I expect—and usually get—from a good .30-06.
.
Not all great new rifles are chambered in .30-06. I suppose that’s a sign of the times. Explains why some younger folks consider it a curiosity. For sure, it’s not as sexy as the hot new numbers. It’s still an accurate, powerful, and versatile choice. And the .30-06 is still out there, hundreds of loads, jillions of rifles…of all vintages.
I am a firm believer in Murphy’s Law: Whatever can go wrong, will. And its First Corollary: At the worst possible time. Mr. Murphy lies in wait for the unwary and unready. In our worlds of shooting and hunting, there are all kinds of things that go wrong. Much can be prevented by preparation but, even with the most careful planning, stuff can still happen.
A cull buck taken on the last day of the ’21 Kansas whitetail season. Boddington missed a much better buck a few days earlier because the elevation turret—with no zero stop—got spun taking the rifle out of a soft case.
Sometimes we do it to ourselves. There’s something to be said for the KISS principle: Keep it simple, stupid. With shooting at longer ranges so popular today, most of us have gone to “dialing holdover” using our elevation turrets. No question, this is the best and most precise way to adjust for distance. With today’s wonderful optics, more consistent than any reticle system.
However, dialing the range is fraught with human error. Can anybody who “dials” a lot honestly say that he/she has never dialed incorrectly? Or, forgotten to return to zero after firing a shot? As common and more dangerous, forgetting to return to zero after not firing a shot?
On this hunt in New Zealand, Boddington chambered a round in his .300 H&H, worked the bolt, and found the bullet stuck in the lands and the magazine packed with propellant granules. Just one reason why it’s essential to run cartridges through the magazine before a hunt.
Not all of today’s great scopes have a solid zero stop. Probably not so critical in competition, but in my view essential on a hunting scope…because stuff happens. In Alaska a couple years ago, young Josh Mayall came into caribou camp with a few days of the season left. He’d be packing during the follow-on brown bear season, but he had a caribou tag. He had the outfitter’s .375, but he’s left-handed like me. I’d just shot a fine caribou, knew my 6.5-.300 Weatherby was zeroed, so I offered it to him, fortunately with plenty of ammo.
Josh and Peter Mayall with Josh’s amazing caribou, taken with Boddington’s 6.5-.300 Weatherby Magnum. After the first shot, the turret dial got spun going through willows; an anti-Murphy miracle that they got this marvelous bull.
Hunting with his father, Pete Mayall, their first afternoon they saw a giant caribou. Josh hit it, then couldn’t hit it again. After the first shot, the caribou and hey needed to cross a thick willow bottom to reposition. All we can figure: Crawling through brush, the elevation turret caught on a branch and spun. Fortunately, the caribou was hit hard; they finally got close enough for a finishing shot. Stuff happens.
Case head separation with a Savage 99 in .300 Savage. Inspection of brass will usually reveal potential cracks…but not always. The only solution on this rifle is to discard cases after one reload.
Happened to me in the ’21 Kansas whitetail season. Easy shot at close range, clean miss. Checked zero, two feet low at 50 yards. That dial got spun hard. I’d had the rifle in a soft case in the four-wheeler that morning, dial must have spun when I took it out of the case in the dark. Depending on the scope, you can usually figure out how much it spun and bring it back to zero. This one had spun a complete revolution. Unlikely, but stuff happens.
Boddington believes a hunting scope needs a solid zero stop on dial-up turret. The current generation of Leupold’s CDS Turret has one of the best turret stops, solid and high visible.
The only real solution is to find a target immediately and make sure. This just happened to me in Africa, good scope with tight turret clicks. Again, spun taking it out of a soft case. Only a few clicks, could have been a full revolution. We went straight to the camp range.
Mr. Murphy lies in wait, but much of the stuff he loves to pounce on is preventable. We can harp on checking screws and straps and such until the cows come home, but we don’t always do it. Ever had a sling break or a sling swivel stud strip out? I’ve had both. Depends on where and when it happens. Can make the rifle a fulcrum, almost certain damage to rifle, scope, or both.
There’s no predicting what load a certain rifle will group best with…until you try. This particular 7mm-08 likes Hornady’s inexpensive American Whitetail load, with plain old 139-grain Interlock bullet.
How carefully do you check your ammo? For hunting, it’s downright dumb to not run every cartridge you’re taking in and out of your chamber. I must not have done that at least once. I was far up on a mountain in New Zealand with a .300 H&H, charged with handloads that shot quarter-inch groups. Accuracy didn’t mean much when I chambered a round, didn’t fire, cleared the rifle, and had a bullet stuck in the lands and a magazine full of propellent. The latter was a matter of dumping and swabbing. The former was a real issue, not like we had a cleaning rod on the mountain. After much experimentation and trimming, I finally crafted a long, straight sapling that could be used as a ramrod.
It was a day past the last day when Boddington took his Wyoming bighorn. Nothing went wrong on this hunt. Just to make sure, after this ram was spotted the previous day, Boddington insisted on checking zero on a rock.
Factory loads are not free of issues, but handloads are more likely to cause ammo problems, for lots of reasons. Just now, I was in South Africa with a gent shooting a .300 WSM. Some of his handloads had been made from full-length-sizing and trimming .325 WSM cases. Sound enough, but he’d held the resizing die a few thousandths loose. Intermittently, some of his cases were refusing to extract. Basically, his rifle became a single-shot…and somebody needed to carry a ramrod on every stalk.
On arrival in Georgia deer camp Boddington opened his gun case to find the stock of his .30-06 snapped off at the wrist. Glue and duct tape, and the rifle was still in perfect zero.
My reloading stuff was packed away for years, back up today with a new reloading shed. I’m loving it, shooting mostly handloads again. I trust my handloads, don’t shoot anyone else’s. However, inspection is constant and continuous. All cases stretch during firing, but cases in rear-locking actions (most lever-actions) are especially notorious. Stretching reduces case life. Properly, we examine fired cases for a “ring” that suggests incipient case head separation. Unfortunately, that ring isn’t always obvious. I was taking my .300 Savage to the range for one more check before a hunt. If there was a tell-tale ring, I didn’t see it. Doesn’t matter, because on firing only the base of case ejected; the rest of the case remained in chamber. No damage but getting the rest of the case out required trip to a gunsmith. That rifle didn’t go on that hunt. In future, I’ll only hunt with that rifle with maximum once-fired brass.
Larry Tremaine brought his suppressor to Kansas deer camp and used it on Boddington’s Mossberg 7mm PRC. Fine, suppressors can be switched back and forth…but it’s essential to check zero.
Although the paperwork is draconian, suppressors are wonderful tools. Provided threads are the same, you can switch a suppressor from one gun to another, handy. Except, almost like switching a scope, you must remember to check zero. I was on a whitetail hunt in Nebraska when my hunting partner missed what might have been the buck of the season. He’d switched his suppressor to a lever-action .45-70 and had forgotten to check zero. Murphy loved it!
In many rifles best accuracy is obtained by seating bullets just off the lands. Important to carefully check Cartridge Overall Length (COL) to make sure cartridges aren’t too long for magazine or chamber. At the range, double-check to make sure.
Hopefully, we all know it’s essential to check a rifle on site or in camp at the start of any hunt. We’ve all failed to do this, but that’s inviting Murphy to join the party. In our Kansas camp, we ask hunters to arrive early afternoon the day before, and I have our range all set up. Last year, just one of my hunters declined to check. Well, you can lead your horse to water, but you can’t make it drink. First morning he missed what he described as “the biggest buck he’d ever seen.”
Too late, we checked his rifle. It was off a couple of inches. Not really enough to cause a miss at the distance he shot, but I like to have things perfect at the start of a hunt.
Before a hunt, Boddington likes to clean at the range…and then fire two fouling shots. This is a good time to run every cartridge you’re taking through the magazine and into the chamber, making sure of smooth chambering and feeding.
Hopefully it doesn’t happen often, but once in a while everybody misses. Usually, I know what I did wrong, but if I’m not sure I like to check zero, just to be certain. Last month, in South Africa, I got into camp early enough to check zero that afternoon. Shooting at plates was a mistake. Always better to shoot a proper target but seemed okay. First day I missed an impala, PH Fred Burchell calling the strike to the left. Hmm, longish shot, felt like I could have been high or low, but to the left didn’t make sense. So, we repaired to the range. Sure enough, the rifle was shooting a bit left.
This Weatherby 6.5-.300 was in perfect zero for a caribou hunt and dropped Boddington’s bull with a 300-yard shot. Boddington then loaned it to a friend and Murphy stepped in. The elevation turret lacked a zero stop and got spun while going through brush.
Stuff happens, and you never know when—or why—a scope might shift zero. On longer hunts, and especially on tough hunts, I like to check zero every few days, just so I don’t unwittingly invite Mr. Murphy to join me. Some hunts are tougher than others. I got my Wyoming bighorn on the eleventh day of a ten-day horseback hunt. The previous afternoon outfitter Ron Dube finally glassed up a mature ram. He was far away, no way we could get on him that afternoon. No way I wanted to mess this up after ten days of tough sledding. I insisted we stop and shoot at a rock, just to be sure. The rifle still in zero, we slept on the mountain that night and shot the ram late the next morning.
Other stuff can happen. Twice I’ve opened gun cases to find stocks broken off at the wrist. I’ve seen two other stocks break in vehicles, and one more from recoil. In case you have any question about which is stronger, wood or synthetic, all five were walnut. Laminate is probably the strongest of all, although the heaviest. Years ago, I got into deer camp in Georgia to find the stock snapped off on my then-favorite .30-06. No spare rifles available, just one more use for duct tape. I fitted it together, wrapped it in duct tape, and went out to check zero. Murphy was there, but I got the last laugh. The rifle was still in perfect zero, shot two nice whitetails with it.
